{"product_id":"intergrain-4l-merbau-ultradeck-timber-decking-oil-b10","title":"Intergrain 4L Merbau UltraDeck Timber Decking Oil","description":"\u003cp\u003eExperience the superior durability of\n\u003cbr\u003e Intergrain UltraDeck Timber Oil\n\u003cbr\u003e , which lasts three times longer than traditional oil-based decking oils. This high-traffic formula ensures professional results with no peeling or blistering, enhancing the natural look of merbau. The water-based oil penetrates deeply into the timber while forming a protective layer on top, providing a durable and long-lasting finish. Achieve a finish to take pride in with this professional-grade formula, perfect for all exterior timber, including decking, fencing, cladding, and outdoor furniture.\n\u003cbr\u003e PREPARATION\n\u003cbr\u003e Maintenance coat of Intergrain UltraDeck Timber Oil:\n\u003cbr\u003e If your existing\n\u003cbr\u003e Intergrain UltraDeck Timber Oil\n\u003cbr\u003e coating is in good condition, clean the surface with\n\u003cbr\u003e Intergrain UltraPrep™ Timber Cleaner\n\u003cbr\u003e .\n\u003cbr\u003e New timber:\n\u003cbr\u003e Treat timber with\n\u003cbr\u003e Intergrain UltraPrep Tannin \u0026amp; Oil Remover\n\u003cbr\u003e . Then clean with\n\u003cbr\u003e Intergrain UltraPrep Timber Cleaner\n\u003cbr\u003e .\n\u003cbr\u003e Grey and weathered with no previous coating:\n\u003cbr\u003e Clean with\n\u003cbr\u003e Intergrain UltraPrep Timber Cleaner\n\u003cbr\u003e . For severely weathered timber, sand back to a fresh surface, remove all sanding dust, then clean with\n\u003cbr\u003e Intergrain UltraPrep Timber Cleaner\n\u003cbr\u003e .\n\u003cbr\u003e Existing coating in poor condition:\n\u003cbr\u003e Remove coating by using a combination of\n\u003cbr\u003e Intergrain UltraPrep Tannin \u0026amp; Oil Remover\n\u003cbr\u003e and power washing. Then clean with\n\u003cbr\u003e Intergrain UltraPrep Timber Cleaner\n\u003cbr\u003e .\n\u003cbr\u003e Paints, varnishes or coatings in varied condition:\n\u003cbr\u003e Paints, varnishes or coatings that have deteriorated unevenly, remove all existing coating by using a coatings stripper or sanding back to bare timber. Then clean with\n\u003cbr\u003e Intergrain UltraPrep Timber Cleaner\n\u003cbr\u003e .\n\u003cbr\u003e Important: If mould is present or if timber is in a mould-prone area, use\n\u003cbr\u003e Intergrain UltraPrep Mould Killer\n\u003cbr\u003e to remove surface mould effectively as the first step of preparing the timber for coating.\n\u003cbr\u003e APPLICATION\n\u003cbr\u003e 1. Remove excess water from the surface and allow the timber to dry for at least 1 hour before coating. Stir\n\u003cbr\u003e Intergrain UltraDeck Timber Oil\n\u003cbr\u003e thoroughly before and during use with a flat blade stirrer.2. Apply\n\u003cbr\u003e Intergrain UltraDeck Timber Oil\n\u003cbr\u003e using the\n\u003cbr\u003e Intergrain DeckBrush\n\u003cbr\u003e (recommended), flat deck applicator, paint brush, or spray (air-assisted airless or airless). Do not use a roller. Apply at the coverage rate of 10-14m²\/L. Do not overspread or apply thinly as insufficient film thickness will result in lap marks and compromise performance and durability. When coating large areas, work in sections, apply long strokes, and use natural breaks in the boards as stopping points. If spraying, it is recommended to back brush to even out the finish and avoid spotting.3. Allow to dry for at least 3 hours, then apply a second coat. If necessary, sand lightly between coats to remove any raised grain.4. A third coat will give extra protection and is required in harsh conditions such as full sun exposure, around pools, and in humid areas or if the first coat was applied on damp or porous timber. Important: All timber is required to be free from dust, mould, and site contaminants prior to coating. Follow all relevant product label instructions when using\n\u003cbr\u003e Intergrain\n\u003cbr\u003e products.\n\u003cbr\u003e MAINTENANCE\n\u003cbr\u003e - Conduct a routine 12-monthly maintenance inspection.- Best protection of the timber and ease of maintenance is ensured if\n\u003cbr\u003e Intergrain UltraDeck Timber Oil\n\u003cbr\u003e is recoated before deterioration of the coating and timber underneath occurs.To refresh timber with significant signs of weathering, greying, or mould, prepare the surface as per the directions under\n\u003cbr\u003e PREPARATION\n\u003cbr\u003e .\n\u003cbr\u003e Features\n\u003cbr\u003e Lasts 3X longer than oil-based decking oils\n\u003cbr\u003e High traffic formula\n\u003cbr\u003e Professional results with no peeling or blistering\u003c\/p\u003e","brand":"Builders Mitre 10","offers":[{"title":"Default Title","offer_id":52088253546789,"sku":null,"price":138.72,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0928\/0172\/8805\/files\/Builders_Mitre_11_4631831f-d2dc-4d98-8689-d8f46b67925f.png?v=1773738923","url":"https:\/\/tradecentre.idlvr.com.au\/products\/intergrain-4l-merbau-ultradeck-timber-decking-oil-b10","provider":"iDlvr","version":"1.0","type":"link"}