Intergrain 4L Merbau UltraDeck Timber Decking Oil
- VendorBuilders Mitre 10
Intergrain 4L Merbau UltraDeck Timber Decking Oil
- VendorBuilders Mitre 10
Experience the superior durability of
Intergrain UltraDeck Timber Oil
, which lasts three times longer than traditional oil-based decking oils. This high-traffic formula ensures professional results with no peeling or blistering, enhancing the natural look of merbau. The water-based oil penetrates deeply into the timber while forming a protective layer on top, providing a durable and long-lasting finish. Achieve a finish to take pride in with this professional-grade formula, perfect for all exterior timber, including decking, fencing, cladding, and outdoor furniture.
PREPARATION
Maintenance coat of Intergrain UltraDeck Timber Oil:
If your existing
Intergrain UltraDeck Timber Oil
coating is in good condition, clean the surface with
Intergrain UltraPrep™ Timber Cleaner
.
New timber:
Treat timber with
Intergrain UltraPrep Tannin & Oil Remover
. Then clean with
Intergrain UltraPrep Timber Cleaner
.
Grey and weathered with no previous coating:
Clean with
Intergrain UltraPrep Timber Cleaner
. For severely weathered timber, sand back to a fresh surface, remove all sanding dust, then clean with
Intergrain UltraPrep Timber Cleaner
.
Existing coating in poor condition:
Remove coating by using a combination of
Intergrain UltraPrep Tannin & Oil Remover
and power washing. Then clean with
Intergrain UltraPrep Timber Cleaner
.
Paints, varnishes or coatings in varied condition:
Paints, varnishes or coatings that have deteriorated unevenly, remove all existing coating by using a coatings stripper or sanding back to bare timber. Then clean with
Intergrain UltraPrep Timber Cleaner
.
Important: If mould is present or if timber is in a mould-prone area, use
Intergrain UltraPrep Mould Killer
to remove surface mould effectively as the first step of preparing the timber for coating.
APPLICATION
1. Remove excess water from the surface and allow the timber to dry for at least 1 hour before coating. Stir
Intergrain UltraDeck Timber Oil
thoroughly before and during use with a flat blade stirrer.2. Apply
Intergrain UltraDeck Timber Oil
using the
Intergrain DeckBrush
(recommended), flat deck applicator, paint brush, or spray (air-assisted airless or airless). Do not use a roller. Apply at the coverage rate of 10-14m²/L. Do not overspread or apply thinly as insufficient film thickness will result in lap marks and compromise performance and durability. When coating large areas, work in sections, apply long strokes, and use natural breaks in the boards as stopping points. If spraying, it is recommended to back brush to even out the finish and avoid spotting.3. Allow to dry for at least 3 hours, then apply a second coat. If necessary, sand lightly between coats to remove any raised grain.4. A third coat will give extra protection and is required in harsh conditions such as full sun exposure, around pools, and in humid areas or if the first coat was applied on damp or porous timber. Important: All timber is required to be free from dust, mould, and site contaminants prior to coating. Follow all relevant product label instructions when using
Intergrain
products.
MAINTENANCE
- Conduct a routine 12-monthly maintenance inspection.- Best protection of the timber and ease of maintenance is ensured if
Intergrain UltraDeck Timber Oil
is recoated before deterioration of the coating and timber underneath occurs.To refresh timber with significant signs of weathering, greying, or mould, prepare the surface as per the directions under
PREPARATION
.
Features
Lasts 3X longer than oil-based decking oils
High traffic formula
Professional results with no peeling or blistering
$138.72
